National Level- Online Quiz on Engineering Workshop
Department of Mechanical Engineering, Bharat Institute of Engineering and Technology, Hyderabad, Telangana, presents a skill development and testing knowledge in various Aspects of Mechanical Engineering
* Attempt the Quiz only once .
* Score will be released only after closing of the quiz .
* If total marks scored is above 60 % of the maximum marks , then E- certificate will be emailed immediately . Or certificate in 2minutes
* Only 100 E – certificates will be emailed per day .
* Link to Register / attempt the Quiz
1) The teeth of hacksaw blade are bent*
â—¾ Towards right
â—¾ Towards left
â—¾ Alternately towards right and left and every third or fourth left straight
â—¾ May be bent in any direction
2) The cross-section of a chisel is usually*
â—¾ Rectangular
â—¾ Square
â—¾ Hexagonal
â—¾ Octagonal
3) A file removes the metal during*
â—¾ Forward stroke
â—¾Return stroke
â—¾ Both forward and return strokes
â—¾ None of these
4) Riddle is used for
â—¾ Smoothing and cleaning out depressions in the mould
â—¾ Cleaning the moulding sand
â—¾ Moistening the sand around the edge before removing pattern
â—¾ Reinforcement of sand in the top part of moulding box
5) The purpose of a gate is to
â—¾ Delivers molten metal into the mould cavity
â—¾ Act as a reservoir for the molten metal
â—¾ Feed the molten metal to the casting in order to compensate for the shrinkage
â—¾ Delivers molten metal from pouring basin to gate
6) A mortise gauge is a
â—¾ Striking tool
â—¾ Planing tool
â—¾ Boring tool
â—¾ Marking tool
7) Green sand is a mixture of
â—¾ 30% sand and 70% clay
â—¾ 50% sand and 50% clay
â—¾ 70% sand and 30% clay
â—¾ 90% sand and 10% clay
8) The dowels are
â—¾ Wooden nails
â—¾ Box nails
â—¾ Wire nails
â—¾ None of these
9) The type of file used for a wood work is
â—¾ Single cut file
â—¾ Double cut file
â—¾ Rasp cut file
â—¾ Any one of these
10) The acetylene cylinder is usually painted with
â—¾ Black colour
â—¾ White colour
â—¾ Maroon colour
â—¾ Yellow colour
11) V-block is used to
â—¾ Check the trueness of flat surfaces
â—¾ Locate centres of round rods
â—¾ Check the surface roughness
â—¾ None of these
12) A file with 20 teeth in 25 mm is called
â—¾ Rough file
â—¾ Bastard file
â—¾ Second cut file
â—¾ Smooth file
13) When a pattern is made in three parts, the top part, is known as a
â—¾ Drag
â—¾ Cheek
â—¾ Cope
â—¾ None of these
14) The purpose of a riser is to
â—¾ Deliver molten metal into the mould cavity
â—¾ Act as a reservoir for the molten metal
â—¾ Feed the molten metal to the casting in order to compensate for the shrinkage
â—¾ Deliver the molten metal from pouring basin to gate
15) Which of the following material can be used for making patterns?
â—¾ Aluminium
â—¾ Wax
â—¾ Lead
â—¾ All of these
Apply Link